AT30 High Strength Acrylic Tie Anchoring Adhesive
Product Description
*For further description please see Simpson Strong-Tie Anchoring and Fastening Systems Catalog.
**Click Load Table icon for product information.
AT High Strength Acrylic-Tie® Anchoring Adhesive
AT Acrylic-Tie® is a two component, high solids, 10:1 ratio acrylic-based adhesive for use as a high strength, anchor-grouting material. Formulated for use in all types of weather, AT is designed to dispense easily and cure at temperatures down to 0°F. Resin and initiator are dispensed and mixed simultaneously through the mixing nozzle. AT meets the physical requirements of ASTM C881, Type I & IV, Grade 3, Classes A, B & C, except Acrylic-Tie is a non-epoxy product formulated for fast cure time.
USES ■Threaded rod anchoring ■Rebar doweling ■Pick-proof sealant around doors, windows and fixtures CODE REPORTS ■ICC-ES ER-5791* (CRM & URM) ■City of L.A. RR 25459* (PDF) ■NSF/ANSI Standard 61 (11in2/5000 gal) (PDF) ■Multiple DOT listings *Applies to all AT products except AT10.
The Load Tables list values based upon results from the most recent testing and may not reflect those in current code reports. Where code jurisdictions apply, consult the current reports for applicable load values.
APPLICATION Surfaces to receive adhesive must be clean and free of frost. The base material temperature must be 0° F or above at the time of installation. For information on installations below 0° F contact Simpson. Mixed material in nozzle can harden in 5–7 minutes. For installations in or through standing water, see Supplemental Topics - Adhesive Anchors for details.
When the concrete temperature is at or below freezing, ensure any holes drilled in advance are free of frost or ice.
INSTALLATION For installation instructions, click here. TEST CRITERIA Anchors installed with AT Acrylic-Tie® adhesive have been tested in accordance with ICC-ES's Acceptance Criteria for Adhesive Anchors (AC58) for the following:
■Seismic/wind loading ■Long-term creep at elevated-temperature ■Static loading at elevated-temperature ■Damp and water-filled holes ■Freeze-thaw conditions ■Critical and minimum edge distance and spacing In addition, anchors installed with AT Acrylic-Tie® adhesive have been tested in accordance with ICC-ES's Acceptance Criteria for Unreinforced Masonry Anchors (AC60) and NSF/ANSI Standard 61, Drinking Water System Components - Health Effects.
SHELF LIFE Twelve months from date of manufacture in unopened cartridge.
STORAGE CONDITIONS For best results store between 32° F - 80° F. Partially used cartridges can be stored for a limited time by leaving nozzle in place. To re-use, attach new nozzle.
COLOR Resin — white, initiator — black When properly mixed, adhesive will be a uniform gray color.
CLEAN UP Uncured material – Wipe up with cotton cloths. If desired scrub area with abrasive, waterbased cleaner and flush with water. If approved, solvents such as ketones (MEK, acetone, etc.), lacquer thinner, or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surfaces to which they are applied. Cured material — Chip or grind off surface.
CHEMICAL RESISTANCE Very good to excellent against distilled water and inorganic acids. Fair to good against organic acids and alkalis, inorganic alkalis, and many organic solvents. Poor against ketones. For more detailed information contact Simpson or see Technical Bulletin T-SAS-CHEMRES08.
The performance of this product results from its unique formulation which is proprietary to Simpson Strong-Tie. The product may also be protected by one or more of U.S. Pats. 5,643,994; 5,965,635; 6,228,207, licensed from ITW.
SUGGESTED SPECIFICATIONS Anchoring adhesive shall be a two-component acrylic based system supplied in manufacturer's standard side-by-side or coaxial cartridge and dispensed through a static-mixing nozzle supplied by the manufacturer. Adhesive shall meet the physical requirements of ASTM C-881 for Type I and IV, Grade 3, Class A, B and C and must develop a minimum 10,210 psi compressive yield strength after 7 day cure. Adhesive must have a heat deflection temperature of a minimum 149°F (65°C). Adhesive shall be Acrylic-Tie® from Simpson Strong-Tie, Pleasanton, CA. Anchors shall be installed per Simpson Strong-Tie instructions for AT Acrylic-Tie® adhesive.
**Click Load Table icon for product information.
AT High Strength Acrylic-Tie® Anchoring Adhesive
AT Acrylic-Tie® is a two component, high solids, 10:1 ratio acrylic-based adhesive for use as a high strength, anchor-grouting material. Formulated for use in all types of weather, AT is designed to dispense easily and cure at temperatures down to 0°F. Resin and initiator are dispensed and mixed simultaneously through the mixing nozzle. AT meets the physical requirements of ASTM C881, Type I & IV, Grade 3, Classes A, B & C, except Acrylic-Tie is a non-epoxy product formulated for fast cure time.
USES ■Threaded rod anchoring ■Rebar doweling ■Pick-proof sealant around doors, windows and fixtures CODE REPORTS ■ICC-ES ER-5791* (CRM & URM) ■City of L.A. RR 25459* (PDF) ■NSF/ANSI Standard 61 (11in2/5000 gal) (PDF) ■Multiple DOT listings *Applies to all AT products except AT10.
The Load Tables list values based upon results from the most recent testing and may not reflect those in current code reports. Where code jurisdictions apply, consult the current reports for applicable load values.
APPLICATION Surfaces to receive adhesive must be clean and free of frost. The base material temperature must be 0° F or above at the time of installation. For information on installations below 0° F contact Simpson. Mixed material in nozzle can harden in 5–7 minutes. For installations in or through standing water, see Supplemental Topics - Adhesive Anchors for details.
When the concrete temperature is at or below freezing, ensure any holes drilled in advance are free of frost or ice.
INSTALLATION For installation instructions, click here. TEST CRITERIA Anchors installed with AT Acrylic-Tie® adhesive have been tested in accordance with ICC-ES's Acceptance Criteria for Adhesive Anchors (AC58) for the following:
■Seismic/wind loading ■Long-term creep at elevated-temperature ■Static loading at elevated-temperature ■Damp and water-filled holes ■Freeze-thaw conditions ■Critical and minimum edge distance and spacing In addition, anchors installed with AT Acrylic-Tie® adhesive have been tested in accordance with ICC-ES's Acceptance Criteria for Unreinforced Masonry Anchors (AC60) and NSF/ANSI Standard 61, Drinking Water System Components - Health Effects.
SHELF LIFE Twelve months from date of manufacture in unopened cartridge.
STORAGE CONDITIONS For best results store between 32° F - 80° F. Partially used cartridges can be stored for a limited time by leaving nozzle in place. To re-use, attach new nozzle.
COLOR Resin — white, initiator — black When properly mixed, adhesive will be a uniform gray color.
CLEAN UP Uncured material – Wipe up with cotton cloths. If desired scrub area with abrasive, waterbased cleaner and flush with water. If approved, solvents such as ketones (MEK, acetone, etc.), lacquer thinner, or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surfaces to which they are applied. Cured material — Chip or grind off surface.
CHEMICAL RESISTANCE Very good to excellent against distilled water and inorganic acids. Fair to good against organic acids and alkalis, inorganic alkalis, and many organic solvents. Poor against ketones. For more detailed information contact Simpson or see Technical Bulletin T-SAS-CHEMRES08.
The performance of this product results from its unique formulation which is proprietary to Simpson Strong-Tie. The product may also be protected by one or more of U.S. Pats. 5,643,994; 5,965,635; 6,228,207, licensed from ITW.
SUGGESTED SPECIFICATIONS Anchoring adhesive shall be a two-component acrylic based system supplied in manufacturer's standard side-by-side or coaxial cartridge and dispensed through a static-mixing nozzle supplied by the manufacturer. Adhesive shall meet the physical requirements of ASTM C-881 for Type I and IV, Grade 3, Class A, B and C and must develop a minimum 10,210 psi compressive yield strength after 7 day cure. Adhesive must have a heat deflection temperature of a minimum 149°F (65°C). Adhesive shall be Acrylic-Tie® from Simpson Strong-Tie, Pleasanton, CA. Anchors shall be installed per Simpson Strong-Tie instructions for AT Acrylic-Tie® adhesive.
- CUSTOMER FEEDBACK *PLEASE READ*
- FREQUENTLY ASKED QUESTIONS
- WOOD & CONCRETE CONSTRUCTION CONNECTORS
- ANCHORING PRODUCTS & FASTENING SYSTEMS
- ARCHITECTURAL PRODUCTS GROUP
- COLD FORMED STEEL CONNECTORS
- SIMPSON STRONG TIE STRONG FRAME
- QUIK DRIVE PRODUCTS & SYSTEMS
- STRONG WALL SHEARWALLS
- STRONG TIE OVERSTOCKED BARGAIN BIN
- SPECIAL REQUESTED & CUSTOM X VERSION PRODUCTS
- GO TO FASTENERSONLY
- GO TO LOCKSETSONLY
- GO TO STAIRPARTSONLY
- GO TO FYPONONLY
- SIMPSON STRONG-TIE CATALOG PDF FILE
- SIMPSON STRONG TIE VIDEO'S
- OTHER PRODUCT LINES AVAILABLE
